Bubble trouble? Learn how to avoid voids in your impressions.

The process of fabricating an indirect restoration takes careful attention to detail at every step – because there are many opportunities for error. But one step stands above the rest as critical to success: impressioning. Here, first impressions matter most, and every step that follows hinges on an accurate impression. In spite of the known importance of the impression, laboratory technicians are often asked to create flawless restorations based on flawed – or incomplete – information. Naturally, there is a hole in this logic. A technician cannot accurately add detail that the impression itself lacks. Only the dentist can provide the information necessary to error-free reproduction. How do you avoid the dreaded void? By using careful, proper technique to create a quality impression, which is the basis of a successful restoration.

Critical areas, critical consequences

Critical areas require exact duplication of detail, such as margins (especially subgingival) and the fine details of tooth preparations for crowns, veneers, onlays or inlays. It’s not easy to compensate for any voids or errors in the first impression. In fact, any flaws can be compounded throughout the rest of the procedure. Gingival displacement and accurate impressioning still pose some of the greatest challenges in dentistry, despite the use of modern impressioning materials. Today’s materials may be more forgiving than their predecessors, but they can’t fully compensate for shortcomings in the procedure. A recent evaluation conducted within a commercial dental laboratory determined that 86% of crown-and-bridge impressions contained at least one detectable error and 55% contained a critical error related to the finish line.¹ Dental practitioners would be well-advised to take greater care to evaluate the quality of their own impressions, rather than passing over minor mistakes – which could be magnified later in the procedure. Soft and hard tissue anatomy, gingival displacement, moisture management and the behavior of impressioning materials are all part of the equation. It’s time to see how a few simple refinements in your technique could add up to greater improvements in your impressions and final restorations.

Troubleshooting voids

So how can clinicians take a better impression the first time? The answers to that question are as many and varied as the causes of distortions and errors. However, by starting with identifying the precise issue with your impression and backtracking to its cause, you can get a better idea of how to move forward. Here are a few top tips for remediating common issues with technique, material or both: Issue: Voids on margin and preparation Causes: • Blood and saliva contamination around preparation • Improper syringe technique • Working time exceeded, flowability already impaired • Air bubbles in elastomer syringe or intra-oral syringe • Tray not seated properly • Storage at elevated temperature Solutions: • Rinse and dry the prepared area properly and stop any bleeding by using appropriate retraction/hemostatic agents. • When syringing wash material, it is important to always let the material “lead” by advancing the tip forward while keeping it fully submerged in wash material. • Select material with sufficient working time (i.e. regular set instead of fast set). Do not exceed working times given in the instructions for use! • Bleed cartridge prior to loading syringe. Keep flow of material consistent. Do not stop and start while loading the syringe. • Slowly (approx. 5 seconds) insert the loaded tray into the mouth parallel to the long axes of the prepared teeth and hold it in place without applying pressure. • Store impression material at room temperature. Polyether and VPS materials usually require different storage temperatures to ensure sufficient working time, and it’s important to refer to each manufacturers’ instructions for use for best practices. Once cured, recommended storage temperatures and conditions will change. For example, 3M polyether impression materials, (like 3M™ Impregum™ Penta™ Impression Material) should be stored at a temperature of 64-77°F (18-25°), while 3M VPS materials (like 3M™ Imprint™ 3 VPS Impression Material) have a recommended storage temperature of 59-77°F (15-25°C). Keep in mind that higher temperatures can reduce material working time, while lower temperatures may increase intra-oral setting times.

CONCLUSION

Getting a thorough, high-quality impression can help save you time and bring you one step closer to restorative success – but it means being detail-oriented yourself. However, by taking the time to review your technique, your materials and common procedure pitfalls, you can avoid voids – and make a better first impression. Want to learn more about common impressioning problems? Download this troubleshooting guide to help identify potential causes and solutions, and to learn the 10 Golden Rules for perfect impressions.